Uddn Uddn

The engine in Kermit is beginning to show the signs of needing a rebuild, so (long story short; savor that while you can) we found a likely candidate on Craigslist. I got up (relatively) early on Saturday and drove the hour and a half to Lucas, TX, where I found Bob to be a very friendly and interesting guy. We could have gabbed for another hour or so, but I wanted to get back home and see if I could get this thing done in time to ride to the BTW chapter meeting on Sunday.

I got started about 1PM. This is Kermit's old engine before the operation began.

Removal of the old engine was a breeze, especially having done it a few times by now. On the other hand, the new engine had a generator and since Kermit isn't wired for a generator, I elected to swap them out. I remember now how involved it actually is to do that. It involved so major a disassembling that I should have changed the carburetor while I was at it.

The carb on the new engine is literally brand new. It, like the oil filler neck, had obviously never had any fluid through them. I was mildly concerned because the carburetor is a 30PICT-1, originally intended for 1300cc engines. I was going to suffer greatly if this turned out to be a 1300, but I was confident that the AE- serial number on the case, the doghouse oil cooler and the 200mm flywheel all pointed to it more likely being a 1600.

The new engine had a threaded insert where the old one had an open hole, and the bolt I had was a D-bolt intended for a starter and wasn't really one for torquing down. It would probably have sufficed, but this is Mama's trike and I don't want it to come loose just because I was too lazy to go buy the right bolt. Of course, where we live, that's a 45 minute round trip, especially if the first place doesn't have it and Blue Bell is on sale.

The clutch was moved over with a minimum of fuss, but I did not have the handy dandy alignment tool, so I eyeballed it. That turns out to have cost me more time that it would have taken to drive into Fort Worth and get my clutch tool from the old house. Unfortunately, it didn't occur to me that it could be that until I had exhausted every other explanation as to why I just couldn't get it to go that last inch. It was in far enough for the splines to engage, but apparently that wasn't enough. I pulled the engine back out (not that it was actually attached), carefully loosened the clutch bolts until I could just scoot the disc and used my socket handle as the closest tool to the proper one. Tightened everything back down and stabbed the engine first try.


The Mr Gasket fuel pump was very easy to put back where it came from on the old engine, but the coil used to be mounted on the back where the doghouse oil cooler is now. I didn't like the stock location, though I can't really define why. So, I put it on the edge of the fan housing, just above the fuel pump. this is kinda ugly from a wiring standpoint, but it's the best compromise without redoing all the wire in the area and the goal here is to have it ready to ride on Sunday.

I had no further trauma and was able to crank the engine and start it, first try, around 11PM.

Now, it didn't run very nicely, which turned out to be because plug wires 2 & 3 were swapped on  the distributor cap, but once that was corrected, I was able to get a decent idle and rev out of it. I don't fit this trike; it is carefully adjusted to fit Gabby (and I guess anyone near her perfect dimensions, which rules me out for I am a couple feet too tall), so a test ride would have to wait for her in the morning. I called it a night around 1AM. 12 hour job.

Sunday morning, Gabby took it for a ride, and armed with the knowledge that the carburetor was probably too small and the centrifugal advance distributor was probably not going to act like the old engine, she a little reluctantly agreed to try taking it to town for the meeting. I finished putting the rest of it together, bumper, air filter, etc and we got ready for the meeting.

It generally ran ok, but developed a tendancy to die at stoplights. Trooper that she is, she tolerated it for nearly 200 miles of round trip riding. We went to the east side of Ft Worth for the BTW meeting, then to Bridgeport to find that our Mother's Day dinner destination closed at 3PM. We went to Sweetie Pie's Ribeyes in Decatur and had steaks and that horrible apple pie that is so bad that they only serve it a few times each year. We took a walk around the square, enjoying the sights. We went from there to Tractor Supply, cause ya just have to, and on home. It was a long day.

The performance of the new engine was, generally, good, maybe a little lackluster, but not without expecting it to be. So, when I got home tonight, I swapped out the 34PICT-3 carburetor and vacuum advance distributor from Kermit's old engine. I had some difficulty getting it to idle really smoothly without setting the idle advance to about 20 BTDC. Full advance wanted to go too far, so I had to back it off a little to about 15 degrees to keep maximum advance below 35 degrees. I didn't touch the carburetor adjustments. Now, it has a little bit of a lopey idle, but revs way quicker than the old engine. Bigger cam? Dunno. We'll see what Gabby's new test drive allows. Hopefully, she can do that during the day tomorrow and if she's happy with it, she might ride it in to work.

Stuff begins with stuff....

I picked up a stack of 24" squares of 16ga mild steel today. Because of the way they cut and order stuff, 24" squares must be ordered in lots of 8. I know that the tank for Puff will take two squares and all the other stuff I envision will take more and more, so I thought 16 would be a good order that will last a while.

Bit O' Metal Trivia...  16 sheets of 2'x2' 16ga weighs 160 pounds, pretty much...

A New Seat for Kermit

Before I get on with the seat, I have some other update duties to perform.

Kermit had started stalling at most stops, especially in such conditions as a freeway exit or getting caught by a light in a long straightaway. He would always start right  back up and and appear to return to normal without issue.

I suspected either of two things, idle circuit adjustment or the throttle cable arrangement, and really, I figured it would be a combination of the two.

Well, spent a good half day dinking with them both to no avail. I found that even sitting in the shop, I was able to duplicate the issue... If I held the engine at 3000 rpm or so, it would die when I closed the throttle. I also noticed that it had a little bit of a miss during that rev.

Then I finally figured it out, having until then ignored the very thing I had installed specifically to catch this kind of problem! The inline fuel pressure gauge was showing 1 PSI. I shut the engine off and was able to squeeze the hose and get the indicator to swing full scale, so it wasn't a bad gauge. Started again and watched the gauge. When running at 3000 rpm, pressure dropped even lower, then about the time the engine would die, the pressure would come back up to 1 PSI. The entire circuit from tank to carburetor is less than three feet as the hose flies.

Long story short (too late), it was the fuel pump. Makes sense... could provide good enough volume to run, though a little lean at higher rpm, then when you come off the throttle, it dies because the idle circuit picks up from the top of fuel bowl. By the time you can restart it, the pump has caught up and filled the bowl. Rinse. Repeat.

So, dashed down to O'Reilly in Decatur (about a 30 minute round trip) and got another fuel pump and a new filter. All hooked up, 5 PSI, can't kill it now.

That day, we went on a ride just short of 150 miles and it didn't (unexpectedly) die once.

So, fast forward a week and I have a new (new to me, anyhow) Hobart AirForce 250ci plasma cutter to play with. Wanted a plasma cutter forever and finally had both the wherewithall to drop a few bucks on one *and* a decent price for a used one on Craigslist. Actually, it's so barely used, it may as well be new.

It can cut.

I chipped the dross off, but this is how it does it.

One of my upcoming projects, and honestly one of the reasons I wanted the plasma torch now, is a replacement fuel tank for the purple trike. That will be made of 16ga mild steel.

In any case, today's project was replacing the seat on Kermit. The old seat came from the basement at American Motorcycle Trading Company in Arlington. It appears to have been a take-off from a modern Indian motorcycle. Decent enough seat, though a trike puts more weight on your tailbone than a motorcycle typically does, so said tailbone can really tell when you've been on a long ride.

After looking at a *LOT* of seats online, mostly boat and tractor seats, we decided to try a particular tractor seat from Northern Tool, which also happened to be on sale for $70.

I knew that it would involve building a bracket of some sort to mount pretty much any seat, so after some test fitting and test sitting (by Gabby; I don't fit on Kermit), I had an idea that 2" square tubing would work pretty well.

There was no easily accesible square tubing to be had on Saturday, but I did get some 2" 90 degree angle from Lowes. Using my schmancy new plasma torch, I learned how not to cut a straight line, then refined the technique until I *could* cut a straight line and zeroed in on a plan to give 2" square tubing in the place I wanted it most, at the ends, by welding a short piece of angle to the span thusly:

The overal bracket is basically U-shaped, with the square "tube" ends holding the back of the seat suspended on a body crossmember and the front sitting on an existing pedestal that I would otherwise just as soon cut out.

I also got to cut out a reduntant piece of metal right where the left rear seat bracket needed to go. I used my welding apron as a blanket to protect wiring and fuel lines from the easily 3-4 second cutting action. This thing rocks. Anyway...

Painted up and bolted in, ready for a seat

I managed to *not* get a pic of the finished seat, but here it is in plywood test garb.

After the seat was tested by Mike Easter, I had Gabby check it out, short of a ride since the trike wasn't back together yet. She had some errands to run, so while she was out, I also wired up to long installed and never connected oil pressure gauge and tachometer. The oil pressure gauge involved replacing the oil pressure switch with an analog sender and a bit of wiring. The oil pressure switch had a wire going up front to the wiring center, but it was not connected. I needed only extend it a foot or so the back of the gauge and wire up a ground for the sender.

The tachometer took a little more because I had to run a wire for it, pushing and threading the wire through the existing loom. Once connected to the breaker point side of the ignition coil, I started the engine up. The oil pressure gauge worked perfectly, but the tach showed double the expected RPM. There is a switch on the back of the tach, a three position switch to choose whether the connected engine is 4, 6 or 8 cylinders, in that order. I think it's probably just labeled wrong because I had to put it in the 8 cylinder position to read sanely on this four.

With those now working, I loosened the bands on the fuel tank and turned it slightly to clear interference it developed with the filler cap and decorative lid.

The trim boards on either side of the seat needed cutting to fit around the new seat bracket, but otherwise, it went back together like a charm.

We took about a forty mile meandering ride through the countryside and so far the seat seems to be helping a lot!

EFI for Sponge Bob Square Trike

I have picked up the first part for the eventual Mega-Squirting of Sponge Bob, a throttle body. It's from a Kawasaki KFX450 ATV. This TB has a 42mm throat, similar to the common *carburetor* throat size for a 1600 engine, so hopefully it will be a good match.

More to come...

Sponge Bob Gets His Stop Back

You may recall when I got Sponge Bob back on the road that the brakes were weak. I did a little hydraulics math and figured out that front brake cylinders might solve the problem.

They do!

Sponge Bob's speedo had stopped working during the time the transaxle was down. During the week, I opened the connector and checked the pins. The seemed a little loose on the sensor coil. Not sure how they would have been stretched, but squeezing the sockets closed a little seems to have restored speedometer function, so now both trikes have speedometers!

Kermit Gets A Speedo

Not the Spandex kind...

I noticed recently that a couple of manufacturers are offerning GPS speedometer sensors for electronic speedometers. Kermit has been without a speedometer since we acquired him. The 2-1/2" Drag Specialties mechanical speedometer appears to work, but the cable was broken. The cable was broken because the cable was too short for where it was mounted and did not allow a generous enough radius to it's bends. I attempted to reuse it with a longer cable, but apparently the nature of the cable's failure has it stuck in the back of the instrument.

I stumbled across a nice LED speedometer by Intellitronix that comes in, appropriately, green. More importantly, Intellitronix also make a GPS speedometer sensor. I had trouble finding it for sale anywhere, but I found that JEGS carries a couple of GPS sensors. Turns out one of them, the least expensive one no less, is the Intellitronix unit!

So, to simplify my ordering, I found a decent VDO speedometer and an Autometer chrome mounting cup, all from JEGS.

The dogs heralded the arrival of the FedEx guy and I got started as soon as I could.

Of course, the first thing is to ensure that the lighting is green. The speedo comes with red and green silicone caps for the backlight bulbs. I will probably one day replace the bulbs with LED versions, but for now, this is green enough.

The mounting location is intended to be temporary. At some point, I will fabricate a bracket to more properly center it between the handlebar tubes, but for now, I'll put it on the left one.

The mounting bracket can accept a hose clamp and/or a pair of screws. I had no appropriately sized hose clamps, so I fudged it with a few wire ties and a single stabilizing screw.

You may note that the screwhead is chewed up a bit. Turns out that the handlebar "tube" is actually a handlebar rod. Threading the screw into it without the benefit of my tap set was a challenge.

Wiring the instrument is very simple, especially when running the lights and speedo on the same power. Three wires, power, ground, speedo in. I followed my usual color codes, orange for switched power, black for ground and gray for sensor.

It looks pretty good in place...

The GPS device is not weather tite, so I installed it in the trunk.

The unit has three LEDs, red for power, yellow for antenna data connection and green for GPS lock.

Ignition on:

The first time, it took about 3 minutes for the GPS lock to come on. Now it takes about 5 seconds.

The default setting for the GPS unit is to provide 8000 pulses per mile. It's pretty simple to set the VDO speedometer to match.

I have verified that it at least indicates a reasonable speed driving across the yard. We'll road test it tomorrow and compare the readings to a Garmin.

While I was running wire in the trunk anyway, I connected the tail/turn/brake lights in the trunk, too.

Kermit Gets A Gift Box

Box from Jeggs arrived today with a basic VDO speedometer, chrome mounting cup and (ta da!) GPS speed sensor!

This sensor receives GPS signals and converts them to the corresponding pulse rate for any programmable electronic speedometer.

More shortly as I install it....